Computer Aided Design (CAD) - s: Burke

Computer Aided Design (CAD) - s: Burke

Computer Aided Design (CAD) Week 10 :: Limits, Fits and Tolerances Limits and Fits Example Application Clearance Fit Interference Fit Limits and Fits - Terminology

Limits and Fits - Terminology CLEARANCE FITS INTERFERENCE FITS TRANSITION FITS POSITIVE

Limits and Fits Background to BS Selected Fits SELECTED FITS NEGATIVE Limits and Fits

Background to BS Selected Fits SELECTED FITS Limits and Fits Classification H11-c11 Extra loose running fit Provides a large clearance. Gives easy assembly.

H9-d10 Loose running fit Used where ease of assembly is required (e.g. pulleys) H9-e9 Easy running fit Suitable for smaller parts, e.g. camshafts etc. H8-f7 Normal running fit Good quality fit which can be easily produced.

H7-g6 Close running or Location fit Expensive to produce. H7-h6 Precision slide or Location fit Precision Slides with good lubrication under constant Temp. Limits and Fits Classification

H7-k6 Push or easy keyring fit Location of parts which are not dismantled often. H7-n6 Tight keyring fit Tight assembly of long parts where H7-k6 isnt sufficient.

H7-p6 Light drive fit Used to secure steel parts. Dismantel & renewal required. H7-s6 Heavy drive fit Permanent assembly of ferrous parts. Shrunk-fit required. Limits and Fits - Question

Consider a Drive pulley and shaft assembly (shaft = 40). The keyway provides positive drive rotation. The required fit is H7-h6. Calculate: the Maximum and Minimum Limits for the size of Hole & Shaft. Limits and Fits - Solution 40 H7 =

+25 upper 0 lower I.E.: Max Limit of Size of Hole: 40 + .025 = 40.025 Min Limit of Size of Hole: 40 0 = 40.000 40 h6 = -16 upper 0 lower

I.E.: Max Limit of Size of Shaft: 40 - .016 = 39.984 Min Limit of Size of Shaft: 40 0 = 40.000 Limits and Fits - AutoCAD Machining and Surface Texture 3.2 Surface Roughness of 3.2 m

(Machining Optional) 3.2 Machining of Surface is Required Machining of Surface (removal of material) is Prohibited!

Machining and Surface Texture All surfaces are to be machined. A value can be added as necessary. Typical Drawing with Surface Roughness

Recently Viewed Presentations

  • Albert Camus - An Absurd Hero

    Albert Camus - An Absurd Hero

    Albert Camus - An Absurd Hero Michel "It's better to bet on this life than on the next." Albert Camus: The smiling Sisyphus Born Nov. 7, 1913 in Mondovi, French Algeria Father dies in 1914 during World War I, only...
  • NPV-Questions - H. Zafer Yuksel

    NPV-Questions - H. Zafer Yuksel

    The Yurdone Corporation wants to set up a private cemetery business. According to the CFO, Barry M. Deep, business is "looking up". As a result, the cemetery project will provide a net cash inflow of $106,000 for the firm during...
  • CHEM 5581: Graduate Level Quantum Chemistry

    CHEM 5581: Graduate Level Quantum Chemistry

    Comic Sans MS Arial Symbol Times New Roman Default Design CHEM 4531: Physical Chemistry II Technicalities(1) Slide 3 Slide 4 Slide 5 Slide 6 Slide 7 Slide 8 Slide 9 Slide 10
  • SNAPSHOTS: SELECTED EQUINE PIROPLASMOSIS AND EQUINE INFECTIOUS ANEMIA

    SNAPSHOTS: SELECTED EQUINE PIROPLASMOSIS AND EQUINE INFECTIOUS ANEMIA

    Florida: Musico - EP May 2018- Lusitano dressage gelding, showing USEF level dressage around the U.S., advertised as imported directly from Spain in 2015. APHIS-VS received complaint letter from another USEF competitor claiming that Musico is EP-positive and he knows...
  • Polycom UC Software 4.1 April 26, 2012

    Polycom UC Software 4.1 April 26, 2012

    Support for Cisco Discovery Protocol. ... The new user interface (UI) looks a lot more like the Skype and Skype for Business clients with a similar color palette and icons. It's a very clean and intuitive look that extends the...
  • CS 620 Advanced Operating Systems - Cleveland State University

    CS 620 Advanced Operating Systems - Cleveland State University

    The default gateway contains info about the network Ids of the other networks in the internetwork, so it can forward the packet to other routers until the packet is eventually delivered to a router connected to the specified destination. This...
  • Residential Space Planning - cmfac.groups.et.byu.net

    Residential Space Planning - cmfac.groups.et.byu.net

    Accessibility. 9'-0" parking space is required. Doors need a 32" clearance. A 60" square required for a 360° wheelchair turn. Countertops should be 30" to 32" high
  • Pluginizing QUIC

    Pluginizing QUIC

    For instance, in the base implementation, wefindoperations for RTO computations, for the preparation of header or to handle new data from the application. In thiscanvas, wecan insert plugins, which are a set of modified or addedprotocolfunctions.