CHAPTER 2 Fundamentals of Electricity Instructor Name: (Your Name) Copyright 2014 Delmar, Cengage Learning Learning Objectives
Relate electrical terms including voltage, current, and resistance to their hydraulic or pneumatic counterpart Explain the relationship among voltage, current and resistance in an electrical circuit Apply Ohms law to simple electrical circuits to determine an unknown voltage, current or resistance Copyright 2014 Delmar, Cengage Learning
Learning Objectives Perform measurements of voltage, current and resistance using a digital multimeter (DMM) Describe the concept of voltage drop across a resistance when current flows through the resistance Demonstrate Kirchhoffs voltage and current law through voltage and current measurements obtained from a series, a parallel, and a seriesparallel circuit Copyright 2014 Delmar, Cengage Learning
Learning Objectives Determine the total circuit resistance in a series, parallel, and series-parallel electrical circuit given the individual resistor values Calculate voltage drops and currents draws in a series, parallel, and seriesparallel circuit, given the individual resistor values and voltage source Copyright 2014 Delmar, Cengage Learning Atoms, Protons and Electrons
Atoms are the smallest possible pieces of any known element Atoms are made up of protons, electrons and neutrons Protons have a positive charge and electrons have a negative charge Like charges repel and opposite charges attract Copyright 2014 Delmar, Cengage Learning Charges Suspended From Strings
Figure 2-6 Charges suspended from strings. Copyright 2014 Delmar, Cengage Learning Atoms, Protons and Electrons Atoms are like a solar system; protons are the sun with electrons orbiting like planets.
Figure 2-7 Copper Atom. Copyright 2014 Delmar, Cengage Learning Displacing Electrons Rubbing two dissimilar materials can strip electrons from one material and add them to the other One material has a positive charge (missing electrons) One material has a negative charge (too many electrons)
An atom with an unequal number of protons and electrons is called an ion Copyright 2014 Delmar, Cengage Learning Displacing Electrons A material with an excess of electrons or protons will attract a material with the opposite charge An atom with more protons than electrons is a positive ion An atom with more electrons than protons is a negative ion
Electrons flow from a location where there is extra electrons to a location that is missing electrons Copyright 2014 Delmar, Cengage Learning Figure 2-8 Opposite charges on the paper and comb cause an attraction. Copyright 2014 Delmar, Cengage Learning Electric Potential
Electric potential exists between two materials, one with excess electrons (negative charge) and one with an absence of electrons (positive charge) Electric potential is know as voltage or electromotive force (EMF) Voltage can be thought of as pressure in an electrical circuit The unit of measurement of voltage or EMF is the volt The symbol for volt is V (truck battery voltage is usually 12V)
Copyright 2014 Delmar, Cengage Learning Electron Flow The flow of electricity is known as electric current Current flow is the number of electrons passing a stationary point in a given period of time 1 coulomb equals 6.25 billon-billion electrons passing a stationary point in a given period of time Current is measured in amperes
The symbol for amperes is A Copyright 2014 Delmar, Cengage Learning Direction of Current Flow A battery has 2 terminals; positive and negative The positive terminal is marked + and the negative is marked Conventional theory; positive to negative Electron theory; negative to positive
Copyright 2014 Delmar, Cengage Learning Figure 2-9 Electron flow is like the movement of cars to the right, while conventional flow is like the movement of spaces to the left. Copyright 2014 Delmar, Cengage Learning Direct and Alternating Current Almost everything on a truck uses direct current (DC) Direct current does not change direction or amplitude
Alternating current changes amplitude and direction of flow continually Copyright 2014 Delmar, Cengage Learning Conductors Conductors are made of materials that allow electron flow with little opposition Conductors on trucks are usually made of copper Free electrons are easily dislodged from the outer most band of an atom and into the outer most
band of the atom next to it The outer most band of an atom is called the valance band Atom with one or two electrons in the valance band make good conductors Copyright 2014 Delmar, Cengage Learning Figure 2-10 Electron flow is like marbles in a tube: a marble that enters the tube on the left is not the same marble that exits the tube on the right.
Copyright 2014 Delmar, Cengage Learning Conductors (continued) Electron flow is believed to be an energy wave that flows through a conductor The energy wave travels near the speed of light (186,000 miles/second) The actual electrons only flow a few inches per hour The energy wave is similar to the energy wave produced when a pool cue strikes a line of closely
lined up pool balls and only the last ball rolls Copyright 2014 Delmar, Cengage Learning Resistance Resistance is the opposition to the flow of electric current Ohm is the unit of measurement of electrical resistance The symbol for ohms is the Greek letter omega ())
Resistors are electrical components with a specific value of resistance Copyright 2014 Delmar, Cengage Learning Wire Resistance All electrical conductors have some resistance even though it may be a small amount Wire resistance increases with the length of the wire, a 10mm wire has 10 times the resistance as a 1mm wire
A tungsten filament in a light bulb uses resistance to heat up and light when electrical current flows through it Copyright 2014 Delmar, Cengage Learning Making Use of Wire Resistance Figure 2-14 Light bulb filament has a much smaller diameter than the wires connected to the light bulb causing an opposition to the flow of
electric current. Figure 2-15 Electrical resistance cause heat and light when electric current flows through the light bulb filament. Copyright 2014 Delmar, Cengage Learning Insulators An insulator is a material that offers a great
deal of resistance to the flow of electrical current The resistance of an insulator is said to be very high Insulators have five or more valence electrons Plastic, rubber, and glass are examples of good insulators Copyright 2014 Delmar, Cengage Learning Ohms Law
Increasing the voltage causes the electrical current flowing through a fixed value of resistance to increase Increasing the resistance while keeping the voltage source held at a fixed value causes the electric current flowing through the resistance to decrease Copyright 2014 Delmar, Cengage Learning Ohms Law (continued)
Voltage Resistance=Current 1 Volt 1 Ohm = 1 ampere ER=I E = Voltage
R = Resistance I = Amperes Copyright 2014 Delmar, Cengage Learning Memorization Aid Figure 2-16 Ohms law memorization aid. Copyright 2014 Delmar, Cengage Learning
Electrical Maps Circuits are the path that electrical current flows Schematics are used to show the layout or relationship of electrical components Schematics are also know as circuit diagrams or wiring diagrams Electrical schematics use symbols to indicate electrical components found in an electrical circuit Copyright 2014 Delmar, Cengage Learning
Common Electrical Symbols Figure 2-17 Electric symbols used to construct electrical schematic. Copyright 2014 Delmar, Cengage Learning
Measuring Pressure Most pressure gauges display the difference between atmospheric pressure and the unknown pressure and reads as PSIG; G= Gauge Some gauges display the difference between an absolute vacuum and the unknown pressure and reads as PSIA; A= Absolute A differential pressure gauge measures the difference between two different gauge ports
Copyright 2014 Delmar, Cengage Learning Measuring Voltage Voltmeters are electrical diagnostic tools that read voltage Voltmeters display the difference in electrical potential (voltage) between two points Most common volt meters are multimeters capable of reading volts, amperes and resistance Test leads are wires with probes that connect
the volt meter to the circuit being tested Copyright 2014 Delmar, Cengage Learning Typical Multimeter Figure 2-22 Digital multimeter. Copyright 2014 Delmar, Cengage Learning
Measuring Voltage (continued) Test leads are typically colored red and black The red lead is installed at the most positive point in the circuit The black lead is installed at the most negative point in the circuit Volt meters are connected to a circuit in parallel Copyright 2014 Delmar, Cengage Learning
Measuring Voltage With a Voltmeter Figure 2-24 Measuring Voltage. Copyright 2014 Delmar, Cengage Learning Measuring Current Current flow through a circuit is measured with an ammeter An ammeter is typically included in a multimeter Ammeters are connected in series in a circuit
Most multimeters have a specific plug for reading current The circuit current can not exceed the maximum amperage rating of the ammeter Copyright 2014 Delmar, Cengage Learning Measuring Current With an Ammeter Figure 2-26 Measuring current with
an ammeter. Copyright 2014 Delmar, Cengage Learning Tech Tip Modern DMM are fantastic tools but have fooled almost every technician at one time or another. One reason for this is just a miniscule amount of voltage present in a circuit when resistance is being measured can result in dramatic resistance measurement errors. The miniscule voltage can be
generated by engine coolant or water in contact with dissimilar metals, as will be explained in more detail in later chapters. If resistance measurements do not make sense, measure the voltage that is present between the two points of which you want to know the resistance. If the DMM displays any voltage, your resistance reading will not be accurate. Copyright 2014 Delmar, Cengage Learning Current Shunts and Amp Probes A current shunt is a known low value of resistance
placed in the circuit. Voltage is measured across the shunt Current can be calculated with Ohms law Clamp on current probes measure the strength of the magnetic field surrounding a wire and converts it to a current value Current probes may also be designed as an input device to a DMM Clamp on probes make troubleshooting easier because the circuit does not have to be opened to make a amperage reading
Copyright 2014 Delmar, Cengage Learning Clamp On Current Probes Figure 2-28 Clamp-on current probes. Copyright 2014 Delmar, Cengage Learning Measuring Resistance Resistance is measured with an ohmmeter If the ohmmeter has a range setting, set to the highest range of unknown resistances
It is better to isolate the component from the rest of the circuit If a negative resistance reading is obtained look for voltage on the circuit Copyright 2014 Delmar, Cengage Learning A Pressure Differential Gauge Figure 2-33 Using a
differential pressure gauge. Copyright 2014 Delmar, Cengage Learning Measuring Voltage and Current in a Series Circuit Figure 2-40 Measuring
voltage drop and current flow. Copyright 2014 Delmar, Cengage Learning Increasing Resistance to 3 Ohms Figure 2-41 Increasing resistance.
Copyright 2014 Delmar, Cengage Learning Measuring Voltage Drops Figure 2-44 Difference in the voltage dropped across unequal series resistors. Copyright 2014 Delmar, Cengage Learning Series Circuit Series circuits have only one path for current flow
The sum of all the voltage drops in a series circuit is equal to the source voltage The total circuit resistance is the sum of all the resistance in the circuit Copyright 2014 Delmar, Cengage Learning Parallel Circuits Parallel circuits contain multiple paths for current flow Voltage drops in a parallel circuit always equal the source voltage
The sum of the current flow in each branch of a parallel circuit is equal to the total current supplied by the voltage source Adding additional parallel resistance decreases the total circuit resistance Total circuit resistance in a parallel circuit is always less then the smallest resistor To calculate total resistance in a parallel circuit use the product over the sum formula Copyright 2014 Delmar, Cengage Learning
Calculating Total Resistance in a Series Parallel Circuits Figure 2-50 Solved seriesparallel circuit. Figure 2-49 Series-parallel simplification progression. Copyright 2014 Delmar, Cengage Learning Metric Prefixes
Figure 2-51 Common metric prefixes used in electrical system troubleshooting. Copyright 2014 Delmar, Cengage Learning Three Resistors in Parallel Figure 2-52 Three resistors in parallel. Note the measured resistance value is less than any of the parallel-connected resistors. Copyright 2014 Delmar, Cengage Learning Summary
A difference in electric potential between two points causes electrons to flow between the two points when a conductive pass is provided between them. Voltage is electrical potential and is measured in volts. Voltage can be thought of as pressure in a hydraulic or pneumatic circuit. The flow of electrons is called current and measured in amperes. An ampere describes a quantity of electrons passing a stationary point per second. Electric current is like the fluid that flows in a hydraulic circuit.
Copyright 2014 Delmar, Cengage Learning Summary (continued) The opposition of electric current flow is called resistance and is measured in ohms. Ohms law mathematically describes the relationship between voltage, current, and resistance. Ohms law indicates that dividing the value of the voltage dropped across a resistance by the value of resistance in ohms yields the current flow through the resistance in amperes. Ohms law can be
manipulated so that when any two quantities are known (voltage, current, or resistance) the third unknown quantity can be calculated. Copyright 2014 Delmar, Cengage Learning Summary (continued) A voltmeter is like a pressure differential gauge in that the difference in electrical potential between two points is being measured. A voltmeter is typically placed in parallel across a component to measure the voltage drop across the component.
An ammeter is like a flow meter in that the quantity of electrons passing a stationary point per second is being measured. An ammeter is always placed in series with the portion of the circuit that the current flow is being measured. Placing an ammeter in parallel with a component can damage the ammeter. Copyright 2014 Delmar, Cengage Learning Summary (continued) An ohmmeter measures resistance and is only used when there are no voltage sources in the
circuit. In a series electrical circuit, there is only one path for current to flow. The current is the same in a series circuit. The voltage dropped across components in a series circuit is proportional to the components resistance value relative to other components in that circuit. Copyright 2014 Delmar, Cengage Learning Summary (continued)
In a parallel electrical circuit, there is more than one path for current flow. The circuit is divided among each parallel path. The greater the resistance of a path, the less current that flows through that path compared to other paths. The voltage dropped across each component in a parallel circuit is the same, regardless of the resistance of that component. Copyright 2014 Delmar, Cengage Learning
Summary (continued) Series-parallel circuits have components that are connected in parallel and in series. The voltage drops and branch currents can be found by determining the equivalent resistance for the entire circuit. The equivalent resistance is then used to determine the total circuit current. The rules of series and parallel circuits are then applied to the circuit to determine the voltage drops and branch currents.
Copyright 2014 Delmar, Cengage Learning
